The bridging cable tray stone is suitable for cables. It has been widely used in industrial production, making the cable tray play a stronger role in metal surface treatment. It is necessary for people here to detail the key points of Shandong cable tray process, and we hope to help you.

　　1、電纜橋架的類型很多，不同類型的表面處理工藝對于以上規定都不相同，所以在發展表面處理工藝時一定要注意對實際問題進行深入分析，選擇合適的工藝。

　　1. There are many types of cable tray, and different types of surface treatment processes have different requirements for the above. Therefore, when developing the surface treatment process, we must pay attention to the in-depth analysis of the actual problems and select the appropriate process.

　　2、在開發曲面解決方案時，在需求融合其實際應用時進行，充分考慮柔性設備的規定，使在應用時更加方便。

　　2. In the development of curved surface solutions, it is carried out when the requirements are integrated into its practical application, and the provisions of flexible equipment are fully considered to make the application more convenient.

　　3、電纜橋架表面處理過程中必須注意電纜配電設備在自然環境中,當時的電纜功效尤為重要,更能襯托的強項和高壓電纜,表面處理技術在時分是關鍵,如果這是更多的優勢,也可以獲得更好的應用效果。

　　3. In the process of cable bridge surface treatment, attention must be paid to the cable distribution equipment in the natural environment. At that time, the cable efficiency is particularly important, and the strength and high-voltage cable can be more set off. The surface treatment technology is the key in the time, if this is more advantage, it can also obtain better application effect.

　　4,表面進行解決方案的需求在很好的充分考慮實際施工過渡的整個過程及其系統的水平,所有項目不僅是簡單的整體規劃和建設,很多不同的需求層次的知識支持,商品表面的解決必須重視這個級別的時候,我們已經應用于一個巨大的進步。

　　4. The demand for surface solution is well considered in the whole process of actual construction transition and the level of the system. All projects are not only simple overall planning and construction, but also supported by many different levels of professional knowledge. We have applied it to a huge progress when the level of commodity surface solution must be emphasized.

　　在整個安裝過程中，禁止載客。如果現場情況確定有必要，有防范措施的設備可以搭載乘客。對于點焊必須在防腐溶液中做好焊接工作，一般由客戶在現場刷防腐漆。

　　During the whole installation process, it is forbidden to carry passengers. If it is necessary to determine the site conditions, the equipment with safety precautions can carry passengers. For spot welding, the welding must be done well in the anti-corrosion solution. Generally, the customer will brush the anti-corrosion paint on the site.

　　電纜橋架敷設時，橋跨節點與支承板點之間的距離應在橋跨的1/4范圍內。對于大跨度橋梁框架，應盡量與支承板相連接。在有彎道或三通的區域，支撐板的點應單獨提起。

　　When laying the cable bridge, the distance between the bridge span node and the supporting plate point shall be within 1 / 4 of the bridge span. For long-span bridge frame, it should be connected with supporting plate as much as possible. In areas with bends or tees, the points of the support plate shall be lifted separately.

　　山東電纜橋架內的電纜由電纜帶或金屬電纜卡環固定。對于水平鋪裝的電纜一般每2m上下設一個支撐點;垂直鋪裝電纜每1-1.5m固定一次，設計標高變化時，梁端固定一次。

　　The cable in Shandong cable tray is fixed by cable belt or metal cable snap ring. Generally, a support point shall be set up every 2m for cables paved horizontally; cables paved vertically shall be fixed once every 1-1.5m; when the design elevation changes, the beam end shall be fixed once.