In order to avoid accidents, high-voltage distribution cabinet power outage is required to strictly follow the process steps of operation! The following edition will give you a brief introduction, I hope you have an understanding of this, in the future do not blindly operate, resulting in unnecessary trouble!

高壓配電柜具體的停送電流程及注意事項如下：

Specific outage current flow and precautions for HV distribution cabinet are as follows:

1．接送電通知，到熱電辦理送電票。

1. Receiving and delivering telegram notice, transacting telegram ticket to thermoelectric power.

2．確認配電柜所在位置，了解其絕緣情況，確保可送電。

2. Confirm the location of the distribution cabinet, understand its insulation, and ensure that electricity can be transmitted.

3．檢查接地刀所在位置，如已接地請斷開，并檢查機構是否復歸。檢查接地刀所在位置的方法：

3. Check the location of the grounding knife, disconnect it if it has been grounded, and check whether the mechanism has returned. Method of checking the location of grounding cutter:

4．檢查斷路器控制電源開關是否在合閘位置。

4. Check whether the power switch controlled by the circuit breaker is in the closing position.

5．檢查斷路器所處位置（工作/隔離）、狀態（合閘/分閘）及儲能情況，在將斷路器小車搖進工作位置前保證斷路器處于分閘狀態、彈簧已儲能。檢查斷路器狀態的方法：檢查儲能情況的方法：

5. Check the position (work/isolation), state (closing/opening) and energy storage of the circuit breaker. Make sure that the circuit breaker is in the opening state and the spring has stored energy before rolling the circuit breaker trolley into the working position. Method of checking the state of circuit breaker: Method of checking energy storage:

斷路器儲能狀態已儲能未儲能斷路器上有儲能指示位一個被拉開的彈簧一個未被拉開的彈簧

Energy storage status of circuit breaker

6．檢查斷路器二次側插頭是否已經插入并牢固。接地開關狀態合閘分閘接地刀指示燈亮滅接地開關聯鎖裝置打開封閉后門板接地開關聯鎖裝置后門板可打開后門板不能打開斷路器狀態合閘分閘斷路器狀態指示燈紅燈亮“｜”綠燈亮“━”斷路器上的狀態指示位合閘“┃”分閘“○”。

6. Check whether the secondary side plug of the circuit breaker has been inserted and secured. Grounding Switch State Switching, Grounding Knife Indicator Lighting, Grounding Switch Interlocking Device Opening Closed Back Door Plate Grounding Switch Interlocking Device Back Door Plate Opening Back Door Plate Can't Open Circuit Breaker State Switching, Circuit Breaker State Indicator Red Light Lighting, Green Lighting, and State Indicator Location Switching on Circuit Breaker Sluice.

7．用搖把將斷路器小車搖進工作位置，確認斷路器已經到位。

7. Roll the circuit breaker cart into the working position with a rocker to confirm that the circuit breaker is in place.

在用搖把搖小車的時候身體應避開斷路器的觀察窗，以免發生意外斷路器從觀察窗彈射出來對人體造成傷害。當搖把無法搖動且斷路器工作位置指示燈亮時說明斷路器小車已經到達工作位置。

When rocking the car with a rocking handle, the body should avoid the observation window of the circuit breaker in order to avoid accidental ejection of the circuit breaker from the observation window causing harm to the human body. When the shaking handle cannot be shaken and the indicator light of the circuit breaker's working position is on, it indicates that the circuit breaker cart has reached the working position.

8．通過綜保確認斷路器已經受電。

8. Confirm that the circuit breaker has been energized by comprehensive insurance.

9．操作完成，通知要求送電單位設備已經送電。

9. When the operation is completed, the notification requests that the equipment of the transmission unit has been delivered.

感謝您的閱讀與觀看，本文的精彩內容來自：山東航豐電纜橋架，我們會有更多的精彩內容繼續為您呈現，詳情請點擊：http://www.12xw.com

Thank you for your reading and watching. The wonderful content of this article comes from: Shandong Hangfeng Cable Bridge, we will have more wonderful content to continue to show you. For more details, please click: http://www.12xw.com.